Electronic Modules

Sort By:  
ESP-01 Module
$5.00
PixAmp v2.0 - a high current pixel controller
Out of Stock
$30.00
Wireless E1.31 Pixel controller
$0.00
ESP-01 USB Programming Module
$5.50
Wireless E1.31 Pixel controller
$27.50
ESP-01 Module (ESP-01 Module)
ESP-01 Module
ESP-01 Module
$5.00
PixAmp v2.0 (PixAmp v2.0)
PixAmp v2.0 Accepts WS2811 pixel data and provides 3 x high current outputs (Red, Green and Blue) that act as one pixel on a data stream. This product is on back-order.
PixAmp v2.0 - a high current pixel controller
Out of Stock
$30.00
Wixel PRO v1.0 (Wixel PRO v1.0)
The Wixel PRO is a wireless E1.31 sACN pixel controller designed to control a single strand of pixels. See photos for connection information. Pixel limitations are mostly based upon your desired refresh rate, around 680 pixels (4 universes) for a 25ms E1.31 source rate. MQTT support is provided as well for integration into home automation systems where an E1.31 source may not be present. This is all made possible by the fantastic ESPixelStick firmware found here https://github.com/forkineye/ESPixelStick

Each Wixel PRO module is supplied with an ESP-07 module, fuse holder, 3A fuse, 2-way and 4-way large terminal blocks, USB type A to micro B cable and a TRACO-POWER DC-DC converter for user assembly. All SMD components will be pre-installed. 

Requires flashing of ESPixelStick firmware found at the above link. Programming interface is provided via on-board USB connection.

If wider WiFi range is required, an optional external 5dBi 2.4GHz antenna with matching cable and bulkhead connector assembly can be purchased for additional cost by ticking the appropriate checkbox above. 

Supply: 4.5V - 13.2V DC

Dimensions: 86.50mm x 48.75mm x 16mm

This kit requires basic/minimal soldering of all through-hole components. Wixel PRO's can be supplied fully assembled for additional cost by ticking the appropriate checkbox above.
Wireless E1.31 Pixel controller
$0.00
ESP-01 USB Programming Module (USBESP-01ProgCH340G)
ESP-01 USB Programming Module

(ESP-01 module not included)

Follow guide's similar to this http://www.arjunsk.com/iot/programming-esp8266-esp-01-using-esp8266-programmer-ch340g-chip-adapter/ to program your ESP-01 module using this CH340G programmer.
ESP-01 USB Programming Module
$5.50
Wixel v1.0 (Wixel v1.0)
The Wixel is a small wireless E1.31 sACN pixel controller designed to control a single strand of pixels. See photos for connection information. Pixel limitations are mostly based upon your desired refresh rate, around 680 pixels (4 universes) for a 25ms E1.31 source rate. MQTT support is provided as well for integration into home automation systems where an E1.31 source may not be present. This is all made possible by the fantastic ESPixelStick firmware found here https://github.com/forkineye/ESPixelStick

Each Wixel module is supplied with an ESP-01 module(512k/1MB flash), header(not shown in above photo), fuse holder, 3A fuse and 6-way micro terminal block for user assembly. All SMD components will be pre-installed. 

Requires flashing of ESPixelStick firmware found at the above link. A programmer for this task can be purchased from here https://shop.vizztech.com.au/index.php?rt=product/product&path=71&product_id=125

Supply: 5V - 12V DC

Dimensions: 50mm x 16mm x 16mm (excluding ESP-01 module and header)

An upgrade of the on-board ESP-01 flash can be purchased for additional cost by ticked the appropriate checkbox above.

This kit requires basic/minimal soldering of all through-hole components. Wixel's can be supplied fully assembled for additional cost by ticking the appropriate checkbox above.
Wireless E1.31 Pixel controller
$27.50
Per Page      1 - 5 of 5
  • 1